{
    "base_id": "GFSA04",
    "chamber_temperature": [
        "45"
    ],
    "customized_plate_temp": [
        "0"
    ],
    "customized_plate_temp_initial_layer": [
        "0"
    ],
    "epoxy_resin_plate_temp": [
        "0"
    ],
    "epoxy_resin_plate_temp_initial_layer": [
        "0"
    ],
    "fan_cooling_layer_time": [
        "60"
    ],
    "fan_max_speed": [
        "40"
    ],
    "fan_min_speed": [
        "0"
    ],
    "filament_cost": [
        "29.95"
    ],
    "filament_flow_ratio": [
        "0.98"
    ],
    "filament_max_volumetric_speed": [
        "16"
    ],
    "filament_notes": [
        "Created 5/5/26 @ 4:46pm from 0.4mm profile knowledge\n\nUpdated 5/12/26 @ 10:38am\n- PA: 0.046 -> 0.024\n\nUpdated 5/12/26 @ 1:03pm\n- Volumetric output: 19.5 -> 16mm^3/s\n\nUpdated 5/12/26 @ 4:05pm\n- Retraction length: 1.2 -> 0.2mm\n\nUpdated 5/14/26 @ 6:32am\n- Max layer time: 30 -> 60s\n- Min layer time: 15 -> 20s\n- Fan speed for overhangs: 50 -> 60%\n\nUpdated 5/14/26 @ 9:40am\n- Fan speed for overhanges: 60 -> 80%\n\nUpdated 5/15/26 @ 11:43am\n- PA: 0.024 -> 0.046\n\nUpdated 5/18/26 @ 8:42am\n- PA: 0.046 -> 0.066"
    ],
    "filament_retract_before_wipe": [
        "70%"
    ],
    "filament_retract_when_changing_layer": [
        "1"
    ],
    "filament_retraction_length": [
        "0.2"
    ],
    "filament_retraction_speed": [
        "40"
    ],
    "filament_settings_id": [
        "3D-Fuel PCTG Pro @Creality K2 Plus 0.6 nozzle"
    ],
    "filament_type": [
        "PCTG"
    ],
    "filament_vendor": [
        "3D-Fuel"
    ],
    "filament_wipe": [
        "1"
    ],
    "filament_wipe_distance": [
        "2"
    ],
    "from": "User",
    "hot_plate_temp": [
        "80"
    ],
    "hot_plate_temp_initial_layer": [
        "80"
    ],
    "inherits": "CR-PETG @Creality K2 Plus 0.6 nozzle",
    "is_custom_defined": "0",
    "name": "3D-Fuel PCTG Pro @Creality K2 Plus 0.6 nozzle",
    "nozzle_temperature": [
        "260"
    ],
    "nozzle_temperature_initial_layer": [
        "260"
    ],
    "nozzle_temperature_range_low": [
        "250"
    ],
    "overhang_fan_speed": [
        "80"
    ],
    "overhang_fan_threshold": [
        "95%"
    ],
    "pressure_advance": [
        "0.066"
    ],
    "reduce_fan_stop_start_freq": [
        "0"
    ],
    "required_nozzle_HRC": [
        "3"
    ],
    "slow_down_layer_time": [
        "20"
    ],
    "slow_down_min_speed": [
        "15"
    ],
    "temperature_vitrification": [
        "84"
    ],
    "textured_plate_temp": [
        "80"
    ],
    "textured_plate_temp_initial_layer": [
        "80"
    ],
    "version": "25.5.28.19"
}