# generated by PrusaSlicer 2.9.2 on 2025-05-21 at 19:24:02 UTC
arc_fitting = emit_center
autoemit_temperature_commands = 1
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bed_custom_model = 
bed_custom_texture = 
bed_shape = 0x0,250x0,250x220,0x220
bed_temperature = 80
bed_temperature_extruder = 0
before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;[layer_z]\n{if layer_z > 150}\nM201 X{interpolate_table(layer_z, (0,7000), (150,7000), (200,4000), (270,2000))} Y{interpolate_table(layer_z, (0,7000), (150,7000), (200,4000), (270,2000))}\n{endif}\n
between_objects_gcode = 
binary_gcode = 1
bottom_fill_pattern = monotonic
bottom_solid_layers = 3
bottom_solid_min_thickness = 0.5
bridge_acceleration = 1500
bridge_angle = 0
bridge_fan_speed = 90
bridge_flow_ratio = 1
bridge_speed = 50
brim_separation = 0.1
brim_type = outer_only
brim_width = 0
chamber_minimal_temperature = 0
chamber_temperature = 0
color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change
colorprint_heights = 
compatible_printers_condition_cummulative = "printer_model=~/(COREONE|COREONEMMU3)/ and nozzle_diameter[0]==0.4 and nozzle_high_flow[0]";"printer_model=~/(COREONE|COREONEMMU3)/ and nozzle_diameter[0]!=0.8 and nozzle_diameter[0]!=0.6 and nozzle_diameter[0]!=0.5 and nozzle_high_flow[0]"
complete_objects = 0
cooling = 1
cooling_tube_length = 20
cooling_tube_retraction = 45
default_acceleration = 3000
default_filament_profile = "Prusament PLA @COREONE HF0.4"
default_print_profile = 0.20mm SPEED @COREONE HF0.4
deretract_speed = 25
disable_fan_first_layers = 3
dont_support_bridges = 0
draft_shield = disabled
duplicate_distance = 6
elefant_foot_compensation = 0.2
enable_dynamic_fan_speeds = 1
enable_dynamic_overhang_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
end_gcode = {if layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+1, max_print_height)} F720 ; Move print head up{endif}\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM141 S0 ; disable chamber control\nM107 ; turn off fan\nG1 X242 Y211 F10200 ; park\nG4 ; wait\nM572 S0 ; reset PA\nM84 X Y E ; disable motors\n; max_layer_z = [max_layer_z]
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 3000
external_perimeter_extrusion_width = 0.55
external_perimeter_speed = 180
external_perimeters_first = 0
extra_loading_move = -52
extra_perimeters = 0
extra_perimeters_on_overhangs = 0
extruder_clearance_height = 33
extruder_clearance_radius = 75
extruder_colour = ""
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 0.99
extrusion_width = 0.45
fan_always_on = 1
fan_below_layer_time = 20
filament_abrasive = 0
filament_colour = #FF8000
filament_cooling_final_speed = 2.5
filament_cooling_initial_speed = 5
filament_cooling_moves = 3
filament_cost = 39.9
filament_density = 1.23
filament_deretract_speed = nil
filament_diameter = 1.75
filament_infill_max_crossing_speed = 110
filament_infill_max_speed = 200
filament_load_time = 10.5
filament_loading_speed = 10
filament_loading_speed_start = 50
filament_max_volumetric_speed = 10
filament_minimal_purge_on_wipe_tower = 35
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_purge_multiplier = 100%
filament_ramming_parameters = "250 100 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387"
filament_retract_before_travel = nil
filament_retract_before_wipe = 50%
filament_retract_layer_change = 0
filament_retract_length = 0.2
filament_retract_length_toolchange = nil
filament_retract_lift = 0.15
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 80
filament_seam_gap_distance = nil
filament_settings_id = "3D-Fuel Pro PCTG @CORE One HF0.4"
filament_shrinkage_compensation_xy = 0%
filament_shrinkage_compensation_z = 0%
filament_soluble = 0
filament_spool_weight = 0
filament_stamping_distance = 45
filament_stamping_loading_speed = 26.5
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = 1.5
filament_travel_ramping_lift = 1
filament_travel_slope = 1
filament_type = PCTG
filament_unload_time = 8.5
filament_unloading_speed = 100
filament_unloading_speed_start = 100
filament_vendor = Generic
filament_wipe = 1
fill_angle = 45
fill_density = 15%
fill_pattern = grid
first_layer_acceleration = 500
first_layer_acceleration_over_raft = 0
first_layer_bed_temperature = 80
first_layer_extrusion_width = 0.55
first_layer_height = 0.2
first_layer_infill_speed = 100
first_layer_speed = 45
first_layer_speed_over_raft = 30
first_layer_temperature = 260
full_fan_speed_layer = 5
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 1
gap_fill_speed = 120
gcode_comments = 0
gcode_flavor = marlin2
gcode_label_objects = firmware
gcode_resolution = 0.008
gcode_substitutions = 
high_current_on_filament_swap = 0
host_type = prusalink
idle_temperature = 70
infill_acceleration = 7000
infill_anchor = 2
infill_anchor_max = 12
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.55
infill_first = 0
infill_overlap = 15%
infill_speed = 300
inherits_cummulative = ;"Generic PETG @MK4S HF0.4";
interface_shells = 0
interlocking_beam = 0
interlocking_beam_layer_count = 2
interlocking_beam_width = 0.8
interlocking_boundary_avoidance = 2
interlocking_depth = 2
interlocking_orientation = 22.5
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
layer_height = 0.28
machine_limits_usage = emit_to_gcode
machine_max_acceleration_e = 5000,2500
machine_max_acceleration_extruding = 7000,2500
machine_max_acceleration_retracting = 2500,1200
machine_max_acceleration_travel = 7000,2500
machine_max_acceleration_x = 10000,2500
machine_max_acceleration_y = 10000,2500
machine_max_acceleration_z = 400,200
machine_max_feedrate_e = 100,100
machine_max_feedrate_x = 350,160
machine_max_feedrate_y = 350,160
machine_max_feedrate_z = 12,12
machine_max_jerk_e = 10,10
machine_max_jerk_x = 10,8
machine_max_jerk_y = 10,8
machine_max_jerk_z = 2,2
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_fan_speed = 40
max_layer_height = 0.3
max_print_height = 270
max_print_speed = 300
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_bead_width = 85%
min_fan_speed = 10
min_feature_size = 25%
min_layer_height = 0.07
min_print_speed = 15
min_skirt_length = 4
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
multimaterial_purging = 140
notes = 
nozzle_diameter = 0.4
nozzle_high_flow = 1
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_0.4n_{layer_height}mm_{printing_filament_types}_{printer_model}_{print_time}.gcode
over_bridge_speed = 50%
overhang_fan_speed_0 = 90
overhang_fan_speed_1 = 90
overhang_fan_speed_2 = 90
overhang_fan_speed_3 = 90
overhang_speed_0 = 15
overhang_speed_1 = 25
overhang_speed_2 = 50
overhang_speed_3 = 80%
overhangs = 1
parking_pos_retraction = 84
pause_print_gcode = M601
perimeter_acceleration = 6000
perimeter_extruder = 1
perimeter_extrusion_width = 0.55
perimeter_generator = arachne
perimeter_speed = 200
perimeters = 2
physical_printer_settings_id = 
post_process = 
prefer_clockwise_movements = 0
print_host = 
print_settings_id = 0.28mm DRAFT @COREONE HF0.4
printer_model = COREONE
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_MODEL_COREONE\nPG\nNO_TEMPLATES
printer_settings_id = Prusa CORE One HF0.4 nozzle
printer_technology = FFF
printer_variant = HF0.4
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
raft_contact_distance = 0.15
raft_expansion = 1.5
raft_first_layer_density = 80%
raft_first_layer_expansion = 3.5
raft_layers = 0
remaining_times = 1
resolution = 0
retract_before_travel = 1.5
retract_before_wipe = 80%
retract_layer_change = 1
retract_length = 0.7
retract_length_toolchange = 0
retract_lift = 0.2
retract_lift_above = 0
retract_lift_below = 269
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 45
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
silent_mode = 1
single_extruder_multi_material = 0
single_extruder_multi_material_priming = 0
skirt_distance = 6
skirt_height = 1
skirts = 0
slice_closing_radius = 0.049
slicing_mode = regular
slowdown_below_layer_time = 7
small_perimeter_speed = 200
solid_infill_acceleration = 6000
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.55
solid_infill_speed = 200
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -5
start_filament_gcode = "M572 S{if nozzle_diameter[0]==0.4}0.05{elsif nozzle_diameter[0]==0.5}0.044{elsif nozzle_diameter[0]==0.6}0.035{elsif nozzle_diameter[0]==0.8}0.022{elsif nozzle_diameter[0]==0.25}0.18{elsif nozzle_diameter[0]==0.3}0.1{else}0{endif} ; Filament gcode\n\nM142 S36 ; set heatbreak target temp"
start_gcode = M17 ; enable steppers\nM862.1 P[nozzle_diameter] A{(filament_abrasive[0] ? 1 : 0)} F{(nozzle_high_flow[0] ? 1 : 0)} ; nozzle check\nM862.3 P "COREONE" ; printer model check\nM862.5 P2 ; g-code level check\nM862.6 P"Input shaper" ; FW feature check\nM115 U6.3.2+10364\n\nM555 X{(min(print_bed_max[0], first_layer_print_min[0] + 32) - 32)} Y{(max(0, first_layer_print_min[1]) - 4)} W{((min(print_bed_max[0], max(first_layer_print_min[0] + 32, first_layer_print_max[0])))) - ((min(print_bed_max[0], first_layer_print_min[0] + 32) - 32))} H{((first_layer_print_max[1])) - ((max(0, first_layer_print_min[1]) - 4))}\n\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\n\n{if chamber_minimal_temperature[initial_tool]!=0}\nM140 S115 ; set bed temp for chamber heating\n{else}\nM140 S[first_layer_bed_temperature] ; set bed temp\n{endif}\n\nM109 R{((filament_notes[0]=~/.*HT_MBL10.*/) ? (first_layer_temperature[0] - 10) : (filament_type[0] == "PC" or filament_type[0] == "PA") ? (first_layer_temperature[0] - 25) : (filament_type[0] == "FLEX") ? 210 : 170)} ; wait for temp\n\nM84 E ; turn off E motor\n\nG28 ; home all without mesh bed level\n\n{if chamber_minimal_temperature[initial_tool]!=0}\n; Min chamber temp section\nM104 S{idle_temperature[initial_tool]} ; set idle temp\nG1 Z10 F720 ; set bed position\nG1 X242 Y-9 F4800 ; set print head position\nM191 S{chamber_minimal_temperature[initial_tool]} ; wait for minimal chamber temp\nM141 S{chamber_temperature[initial_tool]} ; set nominal chamber temp\nM107\nM140 S[first_layer_bed_temperature] ; set bed temp\n{else}\nM141 S{chamber_temperature[initial_tool]} ; set nominal chamber temp\n{endif}\n\n{if first_layer_bed_temperature[initial_tool]<=60}M106 S70{endif}\nG0 Z40 F10000\nM104 T{initial_tool} S{if is_nil(idle_temperature[initial_tool])}100{else}{idle_temperature[initial_tool]}{endif}\nM190 R[first_layer_bed_temperature] ; wait for bed temp\nM107\n\nG29 G ; absorb heat\n\nM109 R{((filament_notes[0]=~/.*HT_MBL10.*/) ? (first_layer_temperature[0] - 10) : (filament_type[0] == "PC" or filament_type[0] == "PA") ? (first_layer_temperature[0] - 25) : (filament_type[0] == "FLEX") ? 210 : 170)} ; wait for MBL temp\n\nM302 S160 ; lower cold extrusion limit to 160C\n\n{if filament_type[initial_tool]=="FLEX"}\nG1 E-4 F2400 ; retraction\n{else}\nG1 E-2 F2400 ; retraction\n{endif}\n\nM84 E ; turn off E motor\n\nG29 P9 X208 Y-2.5 W32 H4\n\n;\n; MBL\n;\nM84 E ; turn off E motor\nG29 P1 ; invalidate mbl & probe print area\nG29 P1 X150 Y0 W100 H20 C ; probe near purge place\nG29 P3.2 ; interpolate mbl probes\nG29 P3.13 ; extrapolate mbl outside probe area\nG29 A ; activate mbl\n\n; prepare for purge\nM104 S{first_layer_temperature[0]}\nG0 X249 Y-2.5 Z15 F4800 ; move away and ready for the purge\nM109 S{first_layer_temperature[0]}\n\nG92 E0\nM569 S0 E ; set spreadcycle mode for extruder\n\n;\n; Extrude purge line\n;\nG92 E0 ; reset extruder position\nG1 E{(filament_type[0] == "FLEX" ? 4 : 2)} F2400 ; deretraction after the initial one\nG0 E5 X235 Z0.2 F500 ; purge\nG0 X225 E4 F500 ; purge\nG0 X215 E4 F650 ; purge\nG0 X205 E4 F800 ; purge\nG0 X202 Z0.05 F8000 ; wipe, move close to the bed\nG0 X199 Z0.2 F8000 ; wipe, move quickly away from the bed\n\nG92 E0\nM221 S100 ; set flow to 100%
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_bottom_contact_distance = 0
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.28
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.4
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 3
support_material_interface_pattern = auto
support_material_interface_spacing = 0.2
support_material_interface_speed = 50%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 120
support_material_style = snug
support_material_synchronize_layers = 0
support_material_threshold = 35
support_material_with_sheath = 0
support_material_xy_spacing = 80%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 30%
temperature = 260
template_custom_gcode = 
thick_bridges = 0
thin_walls = 0
thumbnails = 16x16/QOI, 313x173/QOI, 480x240/QOI, 380x285/PNG
thumbnails_format = PNG
toolchange_gcode = 
top_fill_pattern = monotoniclines
top_infill_extrusion_width = 0.45
top_one_perimeter_type = none
top_solid_infill_acceleration = 2000
top_solid_infill_speed = 100
top_solid_layers = 4
top_solid_min_thickness = 0.7
travel_acceleration = 7000
travel_lift_before_obstacle = 0
travel_max_lift = 1.5
travel_ramping_lift = 1
travel_slope = 1
travel_speed = 350
travel_speed_z = 12
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 1
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe = 0
wipe_into_infill = 0
wipe_into_objects = 0
wipe_tower = 1
wipe_tower_acceleration = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 25
wipe_tower_extra_flow = 250%
wipe_tower_extra_spacing = 110%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
wiping_volumes_matrix = 0
wiping_volumes_use_custom_matrix = 0
xy_size_compensation = 0
z_offset = 0