{
    "bridge_no_support": "1",
    "bridge_speed": "25",
    "brim_type": "no_brim",
    "enable_support": "1",
    "flush_into_support": "0",
    "from": "User",
    "gap_infill_speed": "150",
    "inherits": "0.20 Standard @Snapmaker U1 (0.4 nozzle)",
    "inner_wall_speed": "150",
    "internal_solid_infill_speed": "150",
    "is_custom_defined": "0",
    "max_bridge_length": "0",
    "name": "0.20 3DF PCTG Pro - Breakaway PLA+ @Snapmaker U1 (0.4 nozzle)",
    "notes": "Updated 5/5/26\n- Wipe tower to use PCTG for the outer rib/perimeter. \n-- PLA when used causes delamination\nSpeeds\n- Outer Wall: 200 -> 100mm/s\n- Inner Wall: 300 -> 150mm/s\n- Sparse infill: 270 -> 150mm/s\n- Internal Solid Infill: 250 -> 150mm/s\n- Top Surface: 200 -> 100mm/s\n- Gap Infill: 250 -> 150mm/s\n- Bridge: 50 -> 25mm/s\n\nv2 - Updated 5/5/26 @ 4:01pm\n- Wipe tower purge line spacing 120 -> 150%\n- Maximum wipe tower print speed: 90 -> 50mm/s\n- Updated wipe tower width (was causing errors): 30 -> 29mm\n\nv3 - Updated 5/6/26 @ 4:55pm\n- Support Style: Dafaule -> Tree (Hybrid)\n- On Build Plate Only\n- Interface pattern: Default -> Rectilinear Interlaced\n- Tree support branch distance: 5 -> 2mm\n\nv4 - Updated 5/7/26 @ 9:00am\n- Support style: Default\n- Remove small overhangs: uncheck\n- interface pattern: rectilinear\n- tip diameter 0.8 -> 1mm\n- branch density: 30 -> 60%\n\nUpdated 5/7/26 @ 5:38pm\n- Reduce infill retraction: disabled\n\nUpdated 5/8/26 @ 10:43am\n- Maximum wipe tower print speed: 50 -> 40mm/s",
    "outer_wall_speed": "100",
    "prime_tower_width": "29",
    "print_settings_id": "0.20 3DF PCTG Pro - Breakaway PLA+ @Snapmaker U1 (0.4 nozzle)",
    "raft_first_layer_expansion": "1",
    "reduce_infill_retraction": "0",
    "single_extruder_multi_material_priming": "1",
    "sparse_infill_pattern": "adaptivecubic",
    "sparse_infill_speed": "150",
    "support_bottom_interface_spacing": "0",
    "support_bottom_z_distance": "0",
    "support_filament": "1",
    "support_interface_bottom_layers": "3",
    "support_interface_filament": "4",
    "support_interface_pattern": "rectilinear",
    "support_interface_spacing": "0",
    "support_interface_top_layers": "3",
    "support_on_build_plate_only": "1",
    "support_remove_small_overhang": "0",
    "support_style": "tree_hybrid",
    "support_top_z_distance": "0",
    "top_surface_speed": "100",
    "tree_support_branch_diameter": "1",
    "tree_support_branch_distance": "1",
    "tree_support_brim_width": "0",
    "tree_support_tip_diameter": "1",
    "tree_support_top_rate": "60%",
    "version": "2.2.46.2",
    "wipe_tower_bridging": "0",
    "wipe_tower_extra_spacing": "150%",
    "wipe_tower_filament": "1",
    "wipe_tower_max_purge_speed": "40"
}